Spray Adhesive Starter Kit – 22Kg TensorGrip L40 | 12FT Hose & Spray Glue Gun

Product Use

Fosseway Tapes Tuskbond will bond a wide variety of substrates including:

Wood

Metals

Rubber

Fabric

Most plastics

Cardboard

Polythene

Concrete

Decorative laminates

This spray adhesive can also be used to bond expanded polystyrene when forming a bond to a different substrate. In this instance the product should be used as a one-way stick and only applied to the opposite substrate (do not spray onto the expanded polystyrene).

---

Ideal for:

This adhesive is ideal for permanent bonds which require a good initial bond strength. It provides good temperature resistance and - if protected from contamination - has an open time of several hours.

Please note you should always test a small sample of the materials first to ensure the suitability of the product for the application. For instance, some vinyls contain large amounts of plasticizer which, over time, can migrate and soften the bond. When in doubt, test first.

---

Composition / information on ingredients

Ingredient	CAS	EINECS	Contents %	Health (Class)	Risk (R Phrases)
Butane / Isobutante	106-97-8	203-448-7	20-30	F+	R12
Propane	74-98-6	200-827-9	20-30	F+	R12
Dichloromethane	75-09-2	200-838-9	35-50	Xn	R40

---

Hazards identification information:

Pressurised Container

Extremely flammable. May form a flammable or explosive mixture with air during use. Contains a Category 3 carcinogen. Limited evidence of a carcinogenic effect.

Solvent abuse can kill instantly.

---

First aid measures:

General:

Move the exposed person to fresh air at once.

Eye’s:

Promptly wash eyes with lots of water while lifting the eyelids. Continue to rinse for at least 15 minutes and get medical attention

Inhalation:

Move the exposed person to fresh air at once. Perform artificial respiration if breathing has stopped. Keep the affected person warn and at rest. Get prompt medical attention.

Ingestion:

Rinse mouth thoroughly. Do not induce vomiting. Get medical attention immediately

---

Fire fighting measures:

Extinguishing Media:

Water spray, fog or mist , Carbon dioxide (CO2), foam

Special Fire Fighting Procedures:

Water may be ineffective but use to keep fire-exposed containers cool. If a leak or spill has not ignited, use water spray to disperse vapours and protect men stopping the leak. Water spray may be used to flush spills away and dilute spills to non-flammable mixtures. Use water spray to reduce vapours. Warn fire fighters that pressurised containers are involved.

Unusual Fire & Explosion Hazards:

Makes explosive mixtures with air. Extremely flammable. May explode in a fire. May travel considerable distance to source of ignition and flash back.

---

Accidental Release Measures:

Spill Cleanup Methods:

Extinguish all ignition sources. Provide ventilation. Avoid sparks, flames, heat and smoking. Ventilate. Absorb in vermiculite, dry sand or earth and place into containers. Collect and reclaim or dispose in sealed containers in licensed waste.

---

Handling and Storage Information:

Usage Precautions:

Keep away from heat, sparks and open flame. Read and follow manufacturer's recommendations. Do not spray near a naked flame or any incandescent material.

Storage Precautions:

Flammable/combustible Store at moderate temperatures in dry, well ventilated area. Keep away from heat, sparks and open flame. Protect from sunlight and do not expose to temperatures exceeding 50°C.

Ventilation:

No specific ventilation requirements noted, except this product must not be used in a confined space without good ventilation. If, following workplace assessment, OEL is likely to be exceeded due to use where natural ventilation is insufficient suitable respirator with organic vapour cartridge must be worn.

Skin Protection:

Wear suitable gloves, PVC, if skin contact is likely. Protective clothing with elasticated cuffs. PVC boots.

Eye Protection:

Wear splash-proof eye goggles to prevent any possibility of eye contact.

General:

Do not smoke when using this product.

---

Exposure Controls and Personal Protection:

Ingredient	CAS No.	EINECS	STD	L.T. (8 Hr.TWA)	S.T. (15 MIN)
Dichloromethane	75-09-2	200-838-9	MEL	100 ppm (Sk)	300 ppm (Sk)
Propane	74-98-6	200-827-9		Asphyxiating	Asphyxiating	Bmgv.
Butane / Isobutane	106-97-8	203-448-7	OES	600 ppm	750 ppm
BMGV. = Biological Monitoring Guidance Value listed in EH40

---

Physical and chemical properties

Appearance:

Pressurised container containing a mixture of active ingredients, solvents and propellants.

Odour:

solvent

Physical Data Comments:

A Flash Point method is not available for aerosols but the major hazardous component, the propellant, has a Flash Point of <-40°C with Flammability limits of 9.5% vol. Upper and 1.8%vol Lower. Auto-ignition temperature is 410/580°C.

---

Stability and Reactivity Information

Stability:

Highly volatile

Conditions to avoid:

Avoid heat, flames and other sources of ignition.

---

Disposal Information:

Disposal Methods:

After use ensure that the container is empty and pierce through the disc near the neck prior to disposal. Dispose of in accordance with all local, regional, national and EC Regulations.

---

Transport Information:

	Road (GB):	Road (ADR):
Mark:	Liquefied Gas, Flammable NOS, UN3161,Class2, Div. 2.1	3161, Liquefied Gas, Flammable NOS, 2°F, ADR
Label for Conveyance:	Flammable Gas (Class 2)	Label Model Number 3, Flammable.

---

Not sure if this spray adhesive is right for your requirements?

If you are not sure if this spray adhesive pot is right for your requirements please do not hesitate to contact our friendly sales team on: 0800 652 1054, and we will be happy to assist you.